Finishes

Matte Black

Venetian Bronze

Satin Chrome

Satin Nickel

How to enable/disable programming code on my SmartCode 955?

1) A programming code enables you to make changes without needing to access the programming button. This is ideal for landlords to allow programming from the outside, without access to the interior program button. Please note that once a programming code is enabled, the program button is disabled and can be used only to factory reset the lock. 2) Make sure the door is open. Press and release the program button using the Smartkey tool or a paper clip. You will hear two beeps. 3) Press 3. You will hear once short beep and the keypad will flash green. 4) Press Kwikset button. 5) Enter a programming code. It will be between 4-8 digits. The programming code cannot be the same as any user code. 6) Press Kwikset button. 7) Re-enter programming code. 8) Press Kwikset button. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step 1.

On my Smartcode 955, I'm unable to program a code.

For security reasons the first 4 digits of each user code must be unique, for example you are unable to program 48151 and 48152If you have disabled user codes you will not be able to add user codes.

How to add a permanent or one-time user code on my SmartCode 955?

Make sure the door is open If you have enabled a programming code, enter your programming code, then press Kwikset. You will hear one short beep and then keypad will flash green. Press 1 to add a permanent user code that can be used for entry at all times, until deleted. Press 7 to add a one-time user code. A one-time user code may be used only once, which will be deleted immediately after used (typically used in emergency causes when you need to give one-time access to a person). You will hear one short beep and the keypad will flash green. Press Kwikset Enter a new user code. It must be between 4- 8 digits. For security reasons, the first 4 digits of each user code must be unique. For example, you are unable to program a user code 4-8-1-5-1 as well as a user code 4-8-1-5-2. Press Kwikset. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashed red, it was unsuccessful. Repeat from step 1.

How to enable/disable User Codes on my SmartCode 955?

If user codes are disabled (example: when you go on vacation), the lock can ONLY be operated by the key) 1. Make sure the door is open. 2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. If you have enabled a programming code, enter your programming code, then press Kwikset. You will hear one short beep and the keypad will flash green. 3. Press 6. You will hear one short beep and the keypad will flash green. 4. Press Kwikset. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from STEP 1.

Answer

How do I add/delete a user code on my SmartCode 955?

Add A User Code: Move swiftly during programming. If no digit is pressed for 10 seconds, the system will time out and you will need to restart the procedure. 1) Make sure the door is open. Press and release the program button using the SmartKey tool or a paper clip. You will hear two beeps. 2) Press 1. You will hear one short beep and the keypad will flash green once. 3) Press the Kwikset button4) Enter a user code. It must be between 4-8 digits. WARNING: For security reasons, the first 4 digits of each user code must be unique. For example you are unable to program a user code 1-2-3-4-5 as well as a user code 1-2-3-4-6. 5) Press the Kwikset button 6) You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step 1.Delete A User Code: 1. Make sure the door is open. 2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. If you have enabled a programming code, enter you programming code, then press Kwikset. You will hear one short beep and the keypad will flash green. 3. Press 2 to delete a user code. You will hear one short beep and the keypad will flash green. 4. Press Kwikset5. Enter the user code you wish to delete. Press Kwikset6. Enter the user code again. 7. Press Kwikset. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red. It was unsuccessful. Repeat from step 1.Delete All User Codes: 1. Make sure the door is open. 2. If you have not enabled a programming code, press and release the program button. You will hear two beeps. If you have enabled a programming code, enter your programming code, then press Kwikset. You will hear one short beep and they keypad will flash green. 3. Press 4. You will hear one short beep and the keypad will flash green. 4. Press Kwikset. 5. Enter 9 – 9 – 9 – 9 – 9 – 96. Enter Kwikset. 7. Enter 9 – 9 – 9 – 9 – 9 – 9 8. Press Kwikset. You will hear one long beep and the keypad will flash green if successful. If you hear three beeps and the keypad flashes red, it was unsuccessful. Repeat from step 1.