Skip to Main Content

Home / Support / Electronic / 905 Keywayless Electronic Deadbolt

Support

905 Keywayless Electronic Deadbolt

Finishes

Polished Brass
Venetian Bronze
Satin Nickel

View in Product Catalog

Ask A Question Register Product

Documents

Note: Do not use prints from this website to mark distances. Due to individual printers, dimensions on installation instructions may not print at an accurate scale.

Answers

Support answers found: 12

Choose a Topic

Answer
How do I add/delete a user code on my 905 Keyless Deadbolt?

Add a User Code1. Press PROG button2. You will hear 2 long beeps 3. Press 12 button4. Press PROG button5. You will hear 1 short beep 6. Enter a new 4-8 digit User Code 7. Press PROG button8. You will hear 1 long beep if successful. If you hear 3 beeps, it was unsuccessful. Repeat from step 1 slowlyDeleting a User Code1. Press PROG button2. You will hear 2 long beeps3. Press 34 button4. Press PROG button5. You will hear 1 short beep6. Enter the User Code you wish to delete7. Press PROG button8. You will hear 1 beep if successful. If unsuccessful, you will hear 3 short beeps. Repeat from step 1 slowly.
Read More
Answer
On my 905 Keyless Deadbolt, when the batteries are drained and a 9V battery is connected to the terminals but the lock doesn’t respond.

1. The 9V battery is NOT connected correctly. Flip the 9V battery and try again.2. The 9V battery is drained. Try a new 9V battery.
Read More
Answer
How to set locking and unlocking direction on my 905 Keyless Deadbolt?

Set Locking and Unlocking Direction What is the location of the latch? For left-Locking Latch (If bolt goes left): Press and release PROG. You will hear 2 long beeps. Press lock button Press 1-2 button Press PROG. You will hear 1 long beep. If not, repeat the process from step A. For right-Locking Latch (If bolt goes right): Press and release PROG. You will hear 2 long beeps. Press lock button Press 5-6 button Press PROG. You will hear 1 long beep. If not, repeat the process from step A.
Read More
Answer
How to reset my 905 Keyless Deadbolt?

How to Reset the Lock1. Make sure the door is open and unlocked.2. Press PROG -(for 30 seconds). You will hear 1 long beep.3. Release PROG button4. Press PROG again.5. You will hear 3 long beepsNote: To use the lock, you will have to go through the door handing process and add User Codes.
Read More
Answer
How do I install/replace my 905 Keyless Deadbolt batteries?

If the 4 AA batteries are too low to operate the lock, use a 9-Volt Alkaline battery to temporarily power the lock. Make sure both terminals on the 9-Volt battery touch the terminals below the keypad. When lock has enough power you will hear 3 short beeps. Hold the 9-Volt in place while entering your user code to unlock the door. Continue holding the 9-Volt in position until the door unlocks. Note: If you remove the battery before the door unlocks, you will need to re-enter your user code Remove the terminal cover Hold the battery to the terminals. You will hear beeping to signal you can open door. Press the battery firmly against the terminals, it will beep 3 times. Keep holding the battery firmly and enter your User Code and press the lock button to unlock Replace the terminal cover
Read More
Answer
On my 905 Keyless Deadbolt, the lock doesn’t respond and the keypad doesn’t respond when touched (no beeping is heard).

1. Cables are NOT properly connected. Make sure cables are connected properly. 2. Batteries are drained. Install a fresh set of batteries.
Read More
Answer
On my 905 Keyless Deadbolt, the lock beeps 4 Long Beeps when the keypad is touched but it cannot be locked/unlocked

Door handing has not yet been set. Follow the instructions for left or right door handing.
Read More
Answer
On my 905 Keyless Deadbolt, when the door is closed and the lock/unlock button is pressed to lock/ unlock the door, the motor runs, but the latch doesn’t extend/retract.

The hole in the door frame behind the strike is NOT drilled at least 1 in (25 mm) deep. Make sure the hole in the door frame behind the strike is drilled at least 1 in (25mm) deep. The strike plate is NOT aligned with the latch bolt. Make sure the strike plate is aligned with the latch bolt. If needed, reposition the strike.
Read More
Answer
On my 905 Keyless Deadbolt, door handing and user codes are set and the motor is activated but the lock cannot be locked or unlocked (or the latch runs in the opposite direction).

Incorrect door handing direction. Re-do the door handing instructions.
Read More

Load More Answers

Community Q&As